Code
P0012
AUDI
P — Powertrain
Camshaft variable timing solenoid failure, Engine oil level is too low, The engine is not timed correctly, The engine oil does not meet the manufacturer's requirements, Variable valve timing actuator failure, Worn timing chain
Views:
UK: 35
EN: 77
RU: 48
AI status
Completed
Completed
100%
Causes
- Faulty/blocked camshaft variable timing (VVT) solenoid or valve
- Low engine oil level or degraded/incorrect oil viscosity
- Oil passages clogged with sludge or deposits
- Faulty VVT actuator (stuck or leaking)
- Worn or stretched timing chain, guides or sprockets
- Damaged wiring, poor connector connection or short to power/ground for VVT circuit
Symptoms
- MIL/Check Engine Light illuminated
- Rough idle or unstable idle
- Reduced engine power, hesitation or poor acceleration
- Decreased fuel economy
- Hard starting or extended cranking
- Unusual engine noise (rattle) from timing cover area
What to check
- Read and record freeze frame data and all stored/related DTCs with a capable scan tool
- Check engine oil level, color and service history; verify correct oil grade
- Visually inspect VVT solenoid wiring and connector for damage, corrosion or looseness
- Check camshaft and crankshaft position sensor signals with scan tool or oscilloscope
- Monitor commanded vs actual camshaft angle using OEM-capable scan tool
- Inspect for oil leaks around solenoid and timing cover
Signal parameters
- Camshaft angle actual vs target (degrees)
- VVT solenoid duty cycle / PWM command (%)
- VVT solenoid current draw (A) or coil resistance (Ω)
- Engine oil pressure (kPa/bar or psi)
- Intake/exhaust camshaft position sensor voltages and waveform
- Crankshaft position sensor signal
Diagnostic algorithm
- Safety: Park on level surface, engage parking brake, allow engine to cool before disconnecting components.
- Retrieve codes and freeze frame, note related codes (cam/crank sensors, oil pressure). Clear codes and perform a controlled drive cycle to reproduce P0012.
- Check engine oil level and condition. If low or contaminated, top up or change to correct manufacturer-specified oil and retest. Many VVT issues clear after proper oil service.
- Visually inspect VVT solenoid connector and wiring for corrosion, chafing or poor pin contact. Wiggle test while monitoring live data to see if cam control changes.
- Test VVT solenoid electrical characteristics: measure coil resistance and compare to spec; check supply voltage and ground at connector with key on. If intermittent or out of spec, repair wiring/connector.
- Command the VVT solenoid on/off or variable duty via scan tool while monitoring camshaft actual vs target. If solenoid does not change camshaft angle, remove and bench-test solenoid (apply battery or apply regulated PWM per service procedure).
- If solenoid and wiring are good, inspect oil passages and VVT actuator for sludge or sticking. Remove solenoid/actuator and inspect for varnish or metal debris; clean or replace as required.
- Check oil pressure at idle and under load. Low oil pressure can prevent VVT operation; diagnose oil pump, relief valve or clogged passages if pressure low.
- If cam timing still incorrect after solenoid replacement and oil/system checks, inspect timing chain, guides and tensioner for wear or jumped tooth. This typically requires removal of timing cover and detailed mechanical inspection.
- After repair, clear codes and perform functional tests and a road test with scan tool monitoring cam target vs actual. Verify no recurrence of code.
- If diagnosis stalls or multiple components are suspect, consult OEM service manual for model-specific test plans and possible software updates.
Likely causes
- Low oil level or oil that does not meet manufacturer's viscosity/quality
- Faulty or clogged VVT solenoid
- Electrical fault at VVT solenoid (open, short, corroded connector)
- VVT actuator sticking or hydraulically leaking
- Timing chain/tensioner wear or jump
Fault status
Status
P0012 — Camshaft Position 'A' Timing Over-Advanced (Bank 1). Possible VVT solenoid, oil supply/quality, actuator, or timing chain issue.
Repair difficulty: Hard
Diagnostic time: 1.5-4.0 hours
Similar codes
HTML Workshop Manuals AI manual library for AUDI Click to show available manuals 9
AUDI 2015 A3 Premium Plus, 2D Convertible
HTML ManualAUDI 2015 A3 Premium Plus, 4D Sedan
HTML ManualAUDI 2015 A3 Premium, 2D Convertible Service Manual
HTML ManualAUDI 2015 A3 Premium, 4D Sedan
HTML ManualAUDI 2015 A3 Prestige, 2D Convertible
HTML ManualAUDI 2015 A3 Prestige, 4D Sedan
HTML ManualAUDI 2015 A3 TDI Premium
HTML ManualAUDI 2015 A3 TDI Premium Plus
HTML ManualYour experience will help others
+100 karma for a short comment :)
Was this AI description helpful?
Your feedback helps improve AI descriptions.
👍 Like
0
👎 Dislike
0
Send to email
Code
P0012
Generic
P — Powertrain
A Camshaft Position - Timing Over-Retarded Bank 1
Views:
UK: 36
EN: 81
RU: 45
AI status
Completed
Completed
100%
Causes
- Faulty/blocked camshaft variable timing (VVT) solenoid or valve
- Low engine oil level or degraded/incorrect oil viscosity
- Oil passages clogged with sludge or deposits
- Faulty VVT actuator (stuck or leaking)
- Worn or stretched timing chain, guides or sprockets
- Damaged wiring, poor connector connection or short to power/ground for VVT circuit
Symptoms
- MIL/Check Engine Light illuminated
- Rough idle or unstable idle
- Reduced engine power, hesitation or poor acceleration
- Decreased fuel economy
- Hard starting or extended cranking
- Unusual engine noise (rattle) from timing cover area
What to check
- Read and record freeze frame data and all stored/related DTCs with a capable scan tool
- Check engine oil level, color and service history; verify correct oil grade
- Visually inspect VVT solenoid wiring and connector for damage, corrosion or looseness
- Check camshaft and crankshaft position sensor signals with scan tool or oscilloscope
- Monitor commanded vs actual camshaft angle using OEM-capable scan tool
- Inspect for oil leaks around solenoid and timing cover
Signal parameters
- Camshaft angle actual vs target (degrees)
- VVT solenoid duty cycle / PWM command (%)
- VVT solenoid current draw (A) or coil resistance (Ω)
- Engine oil pressure (kPa/bar or psi)
- Intake/exhaust camshaft position sensor voltages and waveform
- Crankshaft position sensor signal
Diagnostic algorithm
- Safety: Park on level surface, engage parking brake, allow engine to cool before disconnecting components.
- Retrieve codes and freeze frame, note related codes (cam/crank sensors, oil pressure). Clear codes and perform a controlled drive cycle to reproduce P0012.
- Check engine oil level and condition. If low or contaminated, top up or change to correct manufacturer-specified oil and retest. Many VVT issues clear after proper oil service.
- Visually inspect VVT solenoid connector and wiring for corrosion, chafing or poor pin contact. Wiggle test while monitoring live data to see if cam control changes.
- Test VVT solenoid electrical characteristics: measure coil resistance and compare to spec; check supply voltage and ground at connector with key on. If intermittent or out of spec, repair wiring/connector.
- Command the VVT solenoid on/off or variable duty via scan tool while monitoring camshaft actual vs target. If solenoid does not change camshaft angle, remove and bench-test solenoid (apply battery or apply regulated PWM per service procedure).
- If solenoid and wiring are good, inspect oil passages and VVT actuator for sludge or sticking. Remove solenoid/actuator and inspect for varnish or metal debris; clean or replace as required.
- Check oil pressure at idle and under load. Low oil pressure can prevent VVT operation; diagnose oil pump, relief valve or clogged passages if pressure low.
- If cam timing still incorrect after solenoid replacement and oil/system checks, inspect timing chain, guides and tensioner for wear or jumped tooth. This typically requires removal of timing cover and detailed mechanical inspection.
- After repair, clear codes and perform functional tests and a road test with scan tool monitoring cam target vs actual. Verify no recurrence of code.
- If diagnosis stalls or multiple components are suspect, consult OEM service manual for model-specific test plans and possible software updates.
Likely causes
- Low oil level or oil that does not meet manufacturer's viscosity/quality
- Faulty or clogged VVT solenoid
- Electrical fault at VVT solenoid (open, short, corroded connector)
- VVT actuator sticking or hydraulically leaking
- Timing chain/tensioner wear or jump
Fault status
Status
P0012 — Camshaft Position 'A' Timing Over-Advanced (Bank 1). Possible VVT solenoid, oil supply/quality, actuator, or timing chain issue.
Repair difficulty: Hard
Diagnostic time: 1.5-4.0 hours
Similar codes
Your experience will help others
+100 karma for a short comment :)
Was this AI description helpful?
Your feedback helps improve AI descriptions.
👍 Like
0
👎 Dislike
0
Send to email
Code
P0012
LAND ROVER
P — Powertrain
Intake camshaft position timing - delayed excessively (bank 1)
Views:
UK: 13
EN: 46
RU: 27
AI status
Completed
Completed
100%
Causes
- Faulty/blocked camshaft variable timing (VVT) solenoid or valve
- Low engine oil level or degraded/incorrect oil viscosity
- Oil passages clogged with sludge or deposits
- Faulty VVT actuator (stuck or leaking)
- Worn or stretched timing chain, guides or sprockets
- Damaged wiring, poor connector connection or short to power/ground for VVT circuit
Symptoms
- MIL/Check Engine Light illuminated
- Rough idle or unstable idle
- Reduced engine power, hesitation or poor acceleration
- Decreased fuel economy
- Hard starting or extended cranking
- Unusual engine noise (rattle) from timing cover area
What to check
- Read and record freeze frame data and all stored/related DTCs with a capable scan tool
- Check engine oil level, color and service history; verify correct oil grade
- Visually inspect VVT solenoid wiring and connector for damage, corrosion or looseness
- Check camshaft and crankshaft position sensor signals with scan tool or oscilloscope
- Monitor commanded vs actual camshaft angle using OEM-capable scan tool
- Inspect for oil leaks around solenoid and timing cover
Signal parameters
- Camshaft angle actual vs target (degrees)
- VVT solenoid duty cycle / PWM command (%)
- VVT solenoid current draw (A) or coil resistance (Ω)
- Engine oil pressure (kPa/bar or psi)
- Intake/exhaust camshaft position sensor voltages and waveform
- Crankshaft position sensor signal
Diagnostic algorithm
- Safety: Park on level surface, engage parking brake, allow engine to cool before disconnecting components.
- Retrieve codes and freeze frame, note related codes (cam/crank sensors, oil pressure). Clear codes and perform a controlled drive cycle to reproduce P0012.
- Check engine oil level and condition. If low or contaminated, top up or change to correct manufacturer-specified oil and retest. Many VVT issues clear after proper oil service.
- Visually inspect VVT solenoid connector and wiring for corrosion, chafing or poor pin contact. Wiggle test while monitoring live data to see if cam control changes.
- Test VVT solenoid electrical characteristics: measure coil resistance and compare to spec; check supply voltage and ground at connector with key on. If intermittent or out of spec, repair wiring/connector.
- Command the VVT solenoid on/off or variable duty via scan tool while monitoring camshaft actual vs target. If solenoid does not change camshaft angle, remove and bench-test solenoid (apply battery or apply regulated PWM per service procedure).
- If solenoid and wiring are good, inspect oil passages and VVT actuator for sludge or sticking. Remove solenoid/actuator and inspect for varnish or metal debris; clean or replace as required.
- Check oil pressure at idle and under load. Low oil pressure can prevent VVT operation; diagnose oil pump, relief valve or clogged passages if pressure low.
- If cam timing still incorrect after solenoid replacement and oil/system checks, inspect timing chain, guides and tensioner for wear or jumped tooth. This typically requires removal of timing cover and detailed mechanical inspection.
- After repair, clear codes and perform functional tests and a road test with scan tool monitoring cam target vs actual. Verify no recurrence of code.
- If diagnosis stalls or multiple components are suspect, consult OEM service manual for model-specific test plans and possible software updates.
Likely causes
- Low oil level or oil that does not meet manufacturer's viscosity/quality
- Faulty or clogged VVT solenoid
- Electrical fault at VVT solenoid (open, short, corroded connector)
- VVT actuator sticking or hydraulically leaking
- Timing chain/tensioner wear or jump
Fault status
Status
P0012 — Camshaft Position 'A' Timing Over-Advanced (Bank 1). Possible VVT solenoid, oil supply/quality, actuator, or timing chain issue.
Repair difficulty: Hard
Diagnostic time: 1.5-4.0 hours
Similar codes
HTML Workshop Manuals AI manual library for LAND ROVER Click to show available manuals 39
LAND ROVER 2018 Discovery HSE Luxury, 3.0L Eng VIN K
HTML ManualLAND ROVER 2018 Discovery HSE Luxury, 3.0L Eng VIN V
HTML ManualLAND ROVER 2018 Discovery HSE, 3.0L Eng VIN K
HTML ManualLAND ROVER 2018 Discovery HSE, 3.0L Eng VIN V
HTML ManualLAND ROVER 2018 Discovery Sport HSE
HTML ManualLAND ROVER 2018 Discovery Sport HSE Luxury
HTML ManualLAND ROVER 2018 Discovery Sport SE
HTML ManualLAND ROVER 2018 Range Rover Autobiography
HTML ManualYour experience will help others
+100 karma for a short comment :)
Was this AI description helpful?
Your feedback helps improve AI descriptions.
👍 Like
0
👎 Dislike
0
Send to email
Code
P0012
MITSUBISHI
P — Powertrain
V.V.T. over retarded
Views:
UK: 18
EN: 49
RU: 32
AI status
Completed
Completed
100%
Causes
- Faulty/blocked camshaft variable timing (VVT) solenoid or valve
- Low engine oil level or degraded/incorrect oil viscosity
- Oil passages clogged with sludge or deposits
- Faulty VVT actuator (stuck or leaking)
- Worn or stretched timing chain, guides or sprockets
- Damaged wiring, poor connector connection or short to power/ground for VVT circuit
Symptoms
- MIL/Check Engine Light illuminated
- Rough idle or unstable idle
- Reduced engine power, hesitation or poor acceleration
- Decreased fuel economy
- Hard starting or extended cranking
- Unusual engine noise (rattle) from timing cover area
What to check
- Read and record freeze frame data and all stored/related DTCs with a capable scan tool
- Check engine oil level, color and service history; verify correct oil grade
- Visually inspect VVT solenoid wiring and connector for damage, corrosion or looseness
- Check camshaft and crankshaft position sensor signals with scan tool or oscilloscope
- Monitor commanded vs actual camshaft angle using OEM-capable scan tool
- Inspect for oil leaks around solenoid and timing cover
Signal parameters
- Camshaft angle actual vs target (degrees)
- VVT solenoid duty cycle / PWM command (%)
- VVT solenoid current draw (A) or coil resistance (Ω)
- Engine oil pressure (kPa/bar or psi)
- Intake/exhaust camshaft position sensor voltages and waveform
- Crankshaft position sensor signal
Diagnostic algorithm
- Safety: Park on level surface, engage parking brake, allow engine to cool before disconnecting components.
- Retrieve codes and freeze frame, note related codes (cam/crank sensors, oil pressure). Clear codes and perform a controlled drive cycle to reproduce P0012.
- Check engine oil level and condition. If low or contaminated, top up or change to correct manufacturer-specified oil and retest. Many VVT issues clear after proper oil service.
- Visually inspect VVT solenoid connector and wiring for corrosion, chafing or poor pin contact. Wiggle test while monitoring live data to see if cam control changes.
- Test VVT solenoid electrical characteristics: measure coil resistance and compare to spec; check supply voltage and ground at connector with key on. If intermittent or out of spec, repair wiring/connector.
- Command the VVT solenoid on/off or variable duty via scan tool while monitoring camshaft actual vs target. If solenoid does not change camshaft angle, remove and bench-test solenoid (apply battery or apply regulated PWM per service procedure).
- If solenoid and wiring are good, inspect oil passages and VVT actuator for sludge or sticking. Remove solenoid/actuator and inspect for varnish or metal debris; clean or replace as required.
- Check oil pressure at idle and under load. Low oil pressure can prevent VVT operation; diagnose oil pump, relief valve or clogged passages if pressure low.
- If cam timing still incorrect after solenoid replacement and oil/system checks, inspect timing chain, guides and tensioner for wear or jumped tooth. This typically requires removal of timing cover and detailed mechanical inspection.
- After repair, clear codes and perform functional tests and a road test with scan tool monitoring cam target vs actual. Verify no recurrence of code.
- If diagnosis stalls or multiple components are suspect, consult OEM service manual for model-specific test plans and possible software updates.
Likely causes
- Low oil level or oil that does not meet manufacturer's viscosity/quality
- Faulty or clogged VVT solenoid
- Electrical fault at VVT solenoid (open, short, corroded connector)
- VVT actuator sticking or hydraulically leaking
- Timing chain/tensioner wear or jump
Fault status
Status
P0012 — Camshaft Position 'A' Timing Over-Advanced (Bank 1). Possible VVT solenoid, oil supply/quality, actuator, or timing chain issue.
Repair difficulty: Hard
Diagnostic time: 1.5-4.0 hours
Similar codes
Your experience will help others
+100 karma for a short comment :)
Was this AI description helpful?
Your feedback helps improve AI descriptions.
👍 Like
0
👎 Dislike
0
Send to email