Toggle Side Panel

Shopping Cart

No products in the basket.

Shopping Cart

No products in the basket.

Close search
Home / DTC / U017E — Communication lost with the pre-tensioner of seat belt 'A'

U017E — Communication lost with the pre-tensioner of seat belt 'A'

Detailed page for trouble code U017E.

32,967codes
59brands
10,506generic
22,461specific
All codes P-codes (Powertrain) B-codes (Body) C-codes (Chassis) U-codes (Network/User) Tesla Alerts
Reset
Code

U017E

LAND ROVER U — Network/User

Communication lost with the pre-tensioner of seat belt 'A'

Brand: LAND ROVER
Type: U — Network/User
Views: UK: 2 EN: 12 RU: 4
AI status
Completed
ready
Completed 100%
Page language: EN

Causes

  • Open, short or intermittent wiring/connectors between pretensioner and SRS/module
  • Corroded or disconnected connector at the pretensioner (under seat) or SRS control module
  • Damaged harness at seat flex points (seat track/slide area)
  • Blown related fuse or poor power/ground to pretensioner/module
  • Faulty seat belt pretensioner module or SRS/airbag control module
  • CAN/LIN bus fault (bus-off, high/low short, termination issue) or multiple module failures

Symptoms

  • SRS/airbag warning lamp illuminated on instrument cluster
  • Diagnostic tool reports U017E (and possibly other SRS/CAN communication codes)
  • Seat belt pretensioner may not arm or may not fire during a deploy event
  • Possible loss of other seat-related functions (seatbelt buckle sensor, occupancy sensor) if on same harness

What to check

  • Read and record all DTCs and freeze frame data with a capable SRS diagnostic scan tool
  • Verify battery voltage is stable (measure with engine off) before diagnostics
  • Visually inspect connectors at the pretensioner (under seat) and SRS/airbag control module for corrosion, damage or loose pins
  • Inspect harness at seat hinge/slide for chafing or broken conductors; perform wiggle test while monitoring communication
  • Check related fuses and power/ground signals to the pretensioner/module
  • Scan CAN/LIN bus for bus errors or other nodes showing comm faults; check for other U-codes

Signal parameters

  • Presence of seatbelt pretensioner module address/messages on the CAN bus (module should poll/respond at defined intervals)
  • CAN bus idle voltages ~2.5 V on CAN_H and CAN_L (differential ~0 V idle), dominant state behavior under load — verify with scope
  • Message frequency/intervals for pretensioner module as shown by OEM scan tool (compare to known-good pattern)
  • 12 V supply and ground at pretensioner connector with ignition on (verify stable voltage)
  • Continuity/resistance of pretensioner squib circuit measured per OEM specification (perform only with battery disconnected and following safety precautions)
  • SRS module power/ignition input signals present when key on

Diagnostic algorithm

  1. Use an OEM-capable SRS diagnostic scanner to read and log all codes and freeze frame data; note related U-codes.
  2. Verify battery condition and voltage; charge if low and re-check codes after stable supply.
  3. Visually inspect connectors and wiring at the affected seat pretensioner and at the airbag control module; look for corrosion, bent pins, water ingress, or pin push-out.
  4. With ignition on, use the scan tool to monitor the presence/timeout of the pretensioner module on the bus while performing a gentle wiggle test of the seat harness and seat movement to reproduce the fault.
  5. Check fuses, power and ground for the SRS and pretensioner circuits. Repair any power/ground issues before further testing.
  6. If bus issues are suspected, use an oscilloscope or high-quality CAN tester to observe CAN_H/CAN_L for noise, missing nodes, or bus-off conditions. Repair short/open/termination faults as required.
  7. For suspected squib wiring faults, disconnect the battery negative and wait the manufacturer-specified time. Then measure continuity/resistance of the squib circuit per OEM procedure. Do not attempt continuity checks with the battery connected.
  8. If wiring and connectors test good, follow OEM procedures to reprogram/initialize or replace the pretensioner module or SRS control module. Ensure correct module coding and perform SRS system checks/initialization after replacement.
  9. Clear codes and perform a road/ignition cycle and SRS system check; verify the U017E does not return and the SRS lamp behavior is normal.
  10. If intermittent or not reproducible, document events, inspect for recent service that may have disturbed connectors, and consider harness repair or module replacement if fault history supports it.

Likely causes

  • Corroded/damaged connector at seat pretensioner due to moisture or wear
  • Broken wires in harness at seat hinge/slide (most common on vehicles with powered seats)
  • Faulty or unpowered pretensioner module (connector pin damage or internal failure)
  • Local CAN communication fault (intermittent bus wiring or missing termination)
  • Recent seat removal/installation or module replacement without proper coding

Fault status

⚠️ Status
Lost communication with seat belt pretensioner 'A' — SRS control does not receive/respond to module messages. Check pretensioner wiring, connector, power/ground, and CAN bus integrity.
🟡 Repair difficulty: Medium
⏱️ Diagnostic time: 1.0-2.5 hours

Similar codes

U0151 U0142 U0121 U0073 U0154
Workshop Manuals

Repair manuals for LAND ROVER

3

Land Rover Defender 300Tdi — Workshop Manual (1996 model year)

Workshop Manual
Defender 300Tdi Years: 1996 Manual in English 7.5 MB
Short description

Official workshop manual for the Land Rover Defender 300Tdi (from 1996 model year). Contains specifications, adjustment, fault diagnosis and step-by-step repair and overhaul procedures for engine, transmission, axles, suspension, brakes, electrical and body. Intended for dealer workshops and trained technicians.

199,00 UAH
Contents
Key sections:
  • 01 INTRODUCTION
  • 04 GENERAL SPECIFICATION DATA
  • 05 ENGINE TUNING DATA
  • 07 GENERAL FITTING REMINDERS
  • 09 LUBRICANTS, FLUIDS AND CAPACITIES
  • 10 MAINTENANCE
  • 12 ENGINE Tdi
  • - Description and operation
  • - Fault diagnosis
  • - Adjustment
  • - Repair and overhaul procedures
  • 19 FUEL SYSTEM Tdi
Buy

Land Rover Defender Workshop Manual Supplement & Body Repair Manual (1999 & 2002 MY)

Workshop Manual
Defender Years: 1999–2002 Manual in English 7.6 MB
Short description

Workshop Manual Supplement and Body Repair Manual for the Land Rover Defender. Includes general specifications, maintenance schedules, tuning data and step‑by‑step repair procedures for engine, transmission, suspension, brakes, electrical and body repairs. Covers Defender models from 1999 and 2002 model years.

199,00 UAH
Contents
Key sections:
  • 01 - INTRODUCTION
  • - Introduction
  • - Dimensions
  • - References
  • - Repairs and replacements
  • - Poisonous substances
  • - Fuel handling precautions
  • - Synthetic rubber
  • - Recommended sealants
  • - Used engine oil precautions
  • - Accessories and conversions
  • - Wheels and tyres
Buy

Land Rover Range Rover — Electrical Library (LRL 0453ENG, 2002)

Workshop Manual
Manual in English Pages: 494 7.1 MB
Short description

Land Rover Range Rover Electrical Library (LRL 0453ENG). Comprehensive manual covering fuse details, earth points, system descriptions, diagnostics and connector pin-outs for electrical troubleshooting and repair. Intended for technicians and service workshops.

199,00 UAH
Contents
Key sections:
  • 1 INTRODUCTION
  • 1.1 About this document
  • 1.2 Battery voltage
  • 1.3 Electrical precautions
  • 1.4 Battery disconnecting / charging
  • 1.5 Disciplines / greases
  • 1.6 Abbreviations
  • 1.7 HeVAC, sensors abbreviations
  • 1.8 How to use this document
  • 1.9 Connector detail format
  • 1.10 Fault diagnosis
  • 1.11 Wire colour codes
Buy
Your experience will help others
+100 karma for a short comment :)
Keep it short and practical. Up to 500 characters.
Send to email

Report

Harassment or bullying behavior
Contains mature or sensitive content
Contains misleading or false information
Contains abusive or derogatory content
Contains spam, fake content or potential malware

Block Member?

Please confirm you want to block this member.

You will no longer be able to:

  • See blocked member's posts
  • Mention this member in posts
  • Invite this member to groups
  • Message this member
  • Add this member as a connection

Please note: This action will also remove this member from your connections and send a report to the site admin. Please allow a few minutes for this process to complete.

Report

You have already reported this .