B0111

Code

Generic B — Body

Camera Washer Actuator H

Brand: Generic

Type: B — Body

Views: UK: 20 EN: 31 RU: 18

AI status

Completed

ready

Completed 100%

Page language: EN

Causes

Open or short in the actuator wiring harness
Poor or corroded connector or terminal at the actuator
Failed washer actuator motor (internal short or open)
Stuck or mechanically jammed actuator/nozzle
Blown fuse or faulty relay supplying the actuator
Faulty body/control module output driver

Symptoms

Camera washer does not operate when commanded
Washer operates continuously or runs without command
Intermittent operation or only works after wiggling connector
Washer motor fuse blows repeatedly
DTC B0111 stored in vehicle body control or camera system

What to check

Scan for additional DTCs in body/camera and BCM modules
Visually inspect actuator, connector and harness for corrosion, damage or water ingress
Check fuse and relay for the washer circuit
With key on, command the washer from the switch or scan tool while observing actuator behavior
Measure voltage at actuator connector (supply and ground) while commanding
Check resistance/continuity of actuator motor leads with connectors disconnected

Signal parameters

Supply voltage (key ON, command active): ~0–14 V (should approach battery voltage when driven)
Command signal: On/off or PWM from module — duty varies when active
Motor coil resistance: typically low (a few ohms to tens of ohms) — shows continuity if good
Return/ground continuity: near 0 ohms to chassis ground
Current draw when running: expected hundreds of mA to a few amps (will rise if actuator is stalled)

Diagnostic algorithm

Retrieve freeze-frame and related DTCs from all modules; note conditions when fault set
Visually inspect actuator, nozzle and fluid lines for mechanical blockage or ice
Inspect connector and wiring for corrosion, bent pins, damage or water intrusion
Check washer circuit fuse and relay; replace if blown and retest
Using a multimeter, measure supply voltage at actuator connector with key ON and during command; verify proper ground
Measure motor coil resistance with connector disconnected to confirm continuity (compare left/right or known-good if available)
Command actuator with scan tool while monitoring voltage/current; if no voltage from module, check upstream fuses/relays and wiring
If wiring and power are good, bench-test actuator by applying regulated 12 V power briefly to confirm motor operation (observe polarity/connector orientation)
If actuator fails bench test, replace actuator; if actuator works but module output is absent or abnormal, inspect wiring and consider BCM/control module driver fault
After repair, clear DTCs and perform function test; verify no reoccurrence under the same conditions

Likely causes

Corroded connector pins at camera washer actuator
Broken or chafed wire shorting to chassis or power
Actuator motor failed due to water ingress
Blown fuse or defective relay feeding actuator circuit
Intermittent module output or damaged driver stage in body control module

Fault status

⚠️ Status

B0111 — Camera Washer Actuator H: electrical/functional fault detected. Check power, ground, wiring, connector and actuator. Clear codes after repair and verify operation.

🟡 Repair difficulty: Medium

⏱️ Diagnostic time: 0.5-2.0 hours

Similar codes

AUDI 11

6-speed manual gearbox 0B1, front-wheel drive — Workshop Manual (Edition 05.2014)

Workshop Manual

Years: 2008 Manual in English Pages: 187 4.9 MB

Short description

Workshop manual for the 6‑speed manual gearbox 0B1 (front‑wheel drive). Includes identification, technical data, gearbox/selector removal & installation procedures, clutch hydraulics, adjustment instructions and front differential service. Applicable to Audi A4, Audi A5 (Coupé, Cabriolet, Sportback) and Audi Q5 as referenced in the manual. Edition: 05.2014.

199,00 UAH

Contents

Key sections:

00 - Technical data
1 Identification
1.1 Gearbox identification
2 Technical data
2.1 Allocation of gearbox to engine
2.1.1 Allocation - Audi A4 2008 ►
2.1.2 Allocation - Audi A5 Coupé 2008 ►, Audi A5 Sportback 2010 ►
2.1.3 Allocation - Audi A5 Cabriolet 2009 ►
2.1.4 Allocation - Audi Q5 2008 ►
2.2 Capacities
3 Transmission layout
3.1 Transmission layout - front‑wheel drive

Buy

Audi A3 (1997) – 1.6L 4-cylinder (2‑valve) Engine Mechanical Components Service Manual (AEH, AKL, APF) – Edition 07.2002

Workshop Manual

Years: 1997 Manual in English Pages: 283 4.3 MB

Short description

Service manual for Audi A3 (1997) 1.6L 4‑cylinder (2‑valve) engines (codes AEH, AKL, APF). Includes technical data, engine removal/installation, crankshaft group, cylinder head and valve gear, lubrication, cooling and exhaust system procedures. Edition 07.2002.

199,00 UAH

Contents

Key sections:

00 - Technical data ............................................................1
1 Technical data ............................................................1
1.1 Technical data .......................................................1
1.2 Engine number .......................................................1
1.3 Engine data ........................................................1
10 - Removing and installing engine ..........................................3
1 Removing and installing engine .........................................3
1.1 Removing and installing engine ....................................3
1.2 Removing - vehicles with engine codes AEH, AKL .....................4
1.3 Removing - vehicles with engine code APF ..........................18
1.4 Detaching engine from gearbox ...................................35
1.5 Attaching engine to repair stand ................................38

Buy

AUDI A3 (2004) Workshop Manual — 2.0L FSI Turbo (4‑cyl, 4‑valve) Engine, Mechanics — Edition 03.2017

Workshop Manual

Years: 2004 Manual in English Pages: 235 3.8 MB

Short description

Official workshop manual for the Audi A3 2.0L FSI turbo engine (mechanics). Includes step‑by‑step removal/install procedures, technical data, tightening torques and diagnostic/repair instructions. Intended for professional garages and experienced technicians.

199,00 UAH

Contents

Key sections:

00 - Technical data
1 Engine number
2 Engine data (code letters AXX, BPY, BWA, BHZ, BZC, CDL — capacity, power, torque, bore/stroke, compression, ignition)
3 Safety precautions
3.1 Working on the fuel system
3.2 Procedure before opening high-pressure section
3.3 Working on the cooling system
3.4 Using testers during road test
3.5 Working on the exhaust system
4 General repair instructions
4.1 Cleanliness rules for fuel/injection/turbo
4.2 Checking fuel system for leaks

Buy

Audi A3 2004 — Electrical System (Workshop Manual, Edition 02.2018)

Workshop Manual

Years: 2004 Manual in English Pages: 150 68.2 MB

Short description

Workshop manual for the Audi A3 (2004) — Electrical system. Includes procedures for battery, starter, alternator, gauges, wipers, exterior/interior lighting and wiring. Edition 02.2018.

199,00 UAH

Contents

Key sections:

List of Workshop Manual Repair Groups
- 27 Starter, current supply, CCS
- 90 Gauges, instruments
- 92 Windscreen wash/wipe system
- 94 Lights, bulbs, switches - exterior
- 96 Lights, bulbs, switches - interior
- 97 Wiring
27 - Starter, current supply, CCS
1 Contact corrosion
2 Battery
2.1 Battery - general notes
2.2 Maintenance-free batteries

Buy

Audi A4 / A4 Cabriolet – 4.2 l V8 (5‑valve, timing chains) – Workshop Manual (Mechanics) – Edition 04.2007

Workshop Manual

Years: 2001–2003 Manual in English Pages: 307 7.3 MB

Short description

Comprehensive workshop manual for Audi A4 (2001) and A4 Cabriolet (2003) with the 4.2 L V8, 5‑valve engine with timing chains (Engine IDs BBK/BHF). Includes step‑by‑step procedures for engine removal/installation, crankshaft and timing chain service, cylinder head/valve gear, lubrication, cooling and exhaust system repairs. Intended for professional technicians and service workshops.

199,00 UAH

Contents

Key sections:

00 - Technical data
1 Engine number
2 Engine data (Codes: BBK / BHF; 4.163 l; 253 kW @7000 rpm; torque 410–420 Nm; bore 84.5 mm; stroke 92.8 mm; compression ratio 11.5; RON 98)
3 Safety precautions
4 General repair instructions (cleanliness, fuel system, contact corrosion)
10 - Removing and installing engine
1 Removing engine - vehicles with manual gearbox
1.1 Removing engine (tools, drain fluids, remove bumper, lock carrier, disconnect wiring, fuel, coolant, A/C lines, suspension components, propshaft, exhaust, support engine on platform, lower assembly)
1.2 Separating engine and gearbox (subframe removal, support sets, remove front exhaust pipes, bolt sequence)
1.3 Securing engine to engine and gearbox stand (lifting tackle, VAS 6095 support)
1.4 Installing engine (clutch remarks, alignment, torque values)
2 Removing and installing engine - vehicles with automatic gearbox (procedure parallels manual gearbox with ATF/torque converter notes)

Buy

Audi A4 / A4 Cabriolet — Auxiliary Heater Workshop Manual (Edition 08.2004)

Workshop Manual

Years: 2001 Manual in English Pages: 259 2.0 MB

Short description

Workshop Manual for Audi A4 and A4 Cabriolet — Auxiliary Heater (Edition 08.2004). Contains self-diagnosis procedures, fault tables, electrical and fuel system checks, final control tests, CO₂ exhaust adjustment and step-by-step removal/installation and repair procedures. Intended for professional workshop use.

199,00 UAH

Contents

Key sections:

01 - Self-diagnosis, electrical checks
1 Auxiliary heater self-diagnosis
1.1 Technical data of self-diagnosis
1.2 Function
1.3 Fault recognition
1.4 Guided fault-finding
1.5 Technical data of self-diagnosis
1.6 Test requirements for self-diagnosis
1.7 Safety precautions
2 Self-diagnosis procedure
2.1 Connecting vehicle diagnostic VAS 5051A/K-wire adapter
2.1.1 Control unit identification

Buy

Audi A4 / A4 Cabriolet (1.8T 4‑cyl turbo) — Motronic Injection & Ignition System Service Manual (Edition 01.2015)

Workshop Manual

Years: 2001 Manual in English Pages: 34 851.0 KB

Short description

Service manual for Audi A4 (2001‑) and A4 Cabriolet (2003‑) with 1.8L 4‑cylinder turbo engines. Covers Motronic fuel injection and ignition systems, diagnostic and maintenance procedures. Includes technical data, removal/installation steps and system checks.

199,00 UAH

Contents

Key sections:

24 - Mixture preparation - injection
1 Safety precautions and rules for cleanliness
1.1 General notes on self-diagnosis
1.2 Safety precautions when using testers and measuring instruments during a road test
1.3 Rules for cleanliness and instructions for working on fuel system
1.4 Checking vacuum system
2 Injection system
2.1 Technical data
2.2 Overview of fitting locations - injection system
3 Intake manifold
3.1 Exploded view - intake manifold
3.2 Removing and installing intake manifold

Buy

Audi A8 (2003) — Electrical System Workshop Manual (Edition 08.2014)

Workshop Manual

Years: 2003 Manual in English Pages: 369 9.1 MB

Short description

Comprehensive workshop manual for the Audi A8 (2003) electrical system — Edition 08.2014. Covers battery, alternator, starter, instrument cluster, wiper/washer systems, exterior/interior lighting and wiring repair procedures with step-by-step illustrations. Includes diagnostic and adjustment procedures and torque/data specifications.

199,00 UAH

Contents

Key sections:

27 - Starter, current supply, CCS
1 Contact corrosion
2 Battery
2.1 Battery - general notes
2.2 Maintenance-free batteries
2.3 Disconnecting and connecting battery
2.4 Removing and installing battery
- Remove luggage compartment side trim (right-side)
- Connect battery charger for back-up power
- Detach earth and positive cables, central venting hose
- Remove battery retainer plate and lift battery out
- Installation notes, adaptation via Vehicle diagnostic tester

Buy

Audi Q4 e-tron (Type F4) - Self-study Programme SSP 685

Workshop Manual

Years: 2021 Manual in English Pages: 186 82.7 MB

Short description

Official Audi Service Training self‑study programme SSP 685 for the Audi Q4 e‑tron (Type F4). Covers body, power units, power transmission, running gear, electrics & electronics, high‑voltage system, thermal management, driver assist and infotainment. Intended for internal service training and technical familiarisation; not a workshop repair manual.

199,00 UAH

Contents

Key sections:

Introduction
- Introduction to Audi Q4 e-tron
- Dimensions
Body
- Body structure and materials
- Joining techniques
- Securing high-voltage battery and force progression
- Body assembly (doors, rear lid, panoramic sunroof)
- Dash panel and centre console
Power units
- Technical data: rear electric motor (VX90)
- Technical data: front electric motor (VX89)

Buy

Audi Q8 (2018) — Electrical System Workshop Manual (Edition 05.2019)

Workshop Manual

Years: 2018 Manual in English Pages: 645 14.8 MB

Short description

Workshop manual for the Audi Q8 (2018) — Electrical System. Includes technical data, safety notes and step‑by‑step repair procedures for battery/charging, starter/alternator, lighting, washer/wiper and wiring. Edition 05.2019.

199,00 UAH

Contents

Key sections:

00 - Technical data
1 Safety precautions
1.1 Safety precautions when working on vehicles with start/stop system
1.2 Safety precautions when using testers and measuring instruments during a road test
1.3 Notes on use and safety for LED headlights and Audi laser lights
2 Repair notes
2.1 Rules for cleanliness
2.2 General notes
2.3 Contact corrosion
2.4 ESD (electrostatic discharge) workplace
2.5 Routing and attachment of lines and wiring
2.6 Identification plates

Buy

Audi Servicing Manual — 7‑Speed Dual Clutch Transmission 0CJ / 0CL / 0CK / 0DN / 0DP / 0HL (Edition 05.2018)

Workshop Manual

Years: 2008–2019 Manual in English Pages: 128 11.1 MB

Short description

Service manual for the 7‑Speed dual‑clutch (DSG) transmissions 0CJ/0CL/0CK/0DN/0DP/0HL fitted to various Audi models. Includes repair information, clutch and gearbox disassembly/assembly, mechatronic and hydraulic system procedures, seals and differential work. Edition 05.2018.

199,00 UAH

Contents

Key sections:

00 - General, Technical Data
1 Repair Information
1.1 General Repair Information
1.2 Contact Corrosion
1.3 ATF Pump, Deactivating and Draining the Hydraulic Pump Reservoir
2 Rules for Cleanliness when Working on DSG® Transmission
30 - Clutch
1 Clutch
1.1 Overview - Flywheel and Dual Clutch
1.2 Flywheel, Removing and Installing
1.3 Dual Clutch, Removing and Installing
1.4 Input Shaft Seal, Replacing

Buy

LAND ROVER 3

Land Rover Defender 300Tdi — Workshop Manual (1996 model year)

Workshop Manual

Defender 300Tdi Years: 1996 Manual in English 7.5 MB

Short description

Official workshop manual for the Land Rover Defender 300Tdi (from 1996 model year). Contains specifications, adjustment, fault diagnosis and step-by-step repair and overhaul procedures for engine, transmission, axles, suspension, brakes, electrical and body. Intended for dealer workshops and trained technicians.

199,00 UAH

Contents

Key sections:

01 INTRODUCTION
04 GENERAL SPECIFICATION DATA
05 ENGINE TUNING DATA
07 GENERAL FITTING REMINDERS
09 LUBRICANTS, FLUIDS AND CAPACITIES
10 MAINTENANCE
12 ENGINE Tdi
- Description and operation
- Fault diagnosis
- Adjustment
- Repair and overhaul procedures
19 FUEL SYSTEM Tdi

Buy

Land Rover Defender Workshop Manual Supplement & Body Repair Manual (1999 & 2002 MY)

Workshop Manual

Defender Years: 1999–2002 Manual in English 7.6 MB

Short description

Workshop Manual Supplement and Body Repair Manual for the Land Rover Defender. Includes general specifications, maintenance schedules, tuning data and step‑by‑step repair procedures for engine, transmission, suspension, brakes, electrical and body repairs. Covers Defender models from 1999 and 2002 model years.

199,00 UAH

Contents

Key sections:

01 - INTRODUCTION
- Introduction
- Dimensions
- References
- Repairs and replacements
- Poisonous substances
- Fuel handling precautions
- Synthetic rubber
- Recommended sealants
- Used engine oil precautions
- Accessories and conversions
- Wheels and tyres

Buy

Land Rover Range Rover — Electrical Library (LRL 0453ENG, 2002)

Workshop Manual

Manual in English Pages: 494 7.1 MB

Short description

Land Rover Range Rover Electrical Library (LRL 0453ENG). Comprehensive manual covering fuse details, earth points, system descriptions, diagnostics and connector pin-outs for electrical troubleshooting and repair. Intended for technicians and service workshops.

199,00 UAH

Contents

Key sections:

1 INTRODUCTION
1.1 About this document
1.2 Battery voltage
1.3 Electrical precautions
1.4 Battery disconnecting / charging
1.5 Disciplines / greases
1.6 Abbreviations
1.7 HeVAC, sensors abbreviations
1.8 How to use this document
1.9 Connector detail format
1.10 Fault diagnosis
1.11 Wire colour codes

Buy

Your experience will help others

+100 karma for a short comment :)

Was this AI description helpful?

Your feedback helps improve AI descriptions.

👍 Like 0 👎 Dislike 0

Send to email

Code

B0111

HUMMER B — Body

Side impact module-Left Rear high and/or low circuits is short to ground or short to voltage

Brand: HUMMER

Type: B — Body

Views: UK: 8 EN: 14 RU: 8

AI status

Completed

ready

Completed 100%

Page language: EN

Causes

Open or short in the actuator wiring harness
Poor or corroded connector or terminal at the actuator
Failed washer actuator motor (internal short or open)
Stuck or mechanically jammed actuator/nozzle
Blown fuse or faulty relay supplying the actuator
Faulty body/control module output driver

Symptoms

Camera washer does not operate when commanded
Washer operates continuously or runs without command
Intermittent operation or only works after wiggling connector
Washer motor fuse blows repeatedly
DTC B0111 stored in vehicle body control or camera system

What to check

Scan for additional DTCs in body/camera and BCM modules
Visually inspect actuator, connector and harness for corrosion, damage or water ingress
Check fuse and relay for the washer circuit
With key on, command the washer from the switch or scan tool while observing actuator behavior
Measure voltage at actuator connector (supply and ground) while commanding
Check resistance/continuity of actuator motor leads with connectors disconnected

Signal parameters

Supply voltage (key ON, command active): ~0–14 V (should approach battery voltage when driven)
Command signal: On/off or PWM from module — duty varies when active
Motor coil resistance: typically low (a few ohms to tens of ohms) — shows continuity if good
Return/ground continuity: near 0 ohms to chassis ground
Current draw when running: expected hundreds of mA to a few amps (will rise if actuator is stalled)

Diagnostic algorithm

Retrieve freeze-frame and related DTCs from all modules; note conditions when fault set
Visually inspect actuator, nozzle and fluid lines for mechanical blockage or ice
Inspect connector and wiring for corrosion, bent pins, damage or water intrusion
Check washer circuit fuse and relay; replace if blown and retest
Using a multimeter, measure supply voltage at actuator connector with key ON and during command; verify proper ground
Measure motor coil resistance with connector disconnected to confirm continuity (compare left/right or known-good if available)
Command actuator with scan tool while monitoring voltage/current; if no voltage from module, check upstream fuses/relays and wiring
If wiring and power are good, bench-test actuator by applying regulated 12 V power briefly to confirm motor operation (observe polarity/connector orientation)
If actuator fails bench test, replace actuator; if actuator works but module output is absent or abnormal, inspect wiring and consider BCM/control module driver fault
After repair, clear DTCs and perform function test; verify no reoccurrence under the same conditions

Likely causes

Corroded connector pins at camera washer actuator
Broken or chafed wire shorting to chassis or power
Actuator motor failed due to water ingress
Blown fuse or defective relay feeding actuator circuit
Intermittent module output or damaged driver stage in body control module

Fault status

⚠️ Status

B0111 — Camera Washer Actuator H: electrical/functional fault detected. Check power, ground, wiring, connector and actuator. Clear codes after repair and verify operation.

🟡 Repair difficulty: Medium

⏱️ Diagnostic time: 0.5-2.0 hours