Toggle Side Panel

Shopping Cart

No products in the basket.

Shopping Cart

No products in the basket.

Close search
Home / DTC / C2008 — Steering Angle Sensor - Implausible Signal

C2008 — Steering Angle Sensor - Implausible Signal

Detailed page for trouble code C2008.

33,006codes
59brands
10,545generic
22,461specific
All codes P-codes (Powertrain) B-codes (Body) C-codes (Chassis) U-codes (Network/User) Tesla Alerts
Reset
Code

C2008

LAND ROVER C — Chassis

Steering Angle Sensor - Implausible Signal

Brand: LAND ROVER
Type: C — Chassis
Views: UK: 8 EN: 12 RU: 8
AI status
Completed
ready
Completed 100%
Page language: EN

Causes

  • Faulty steering angle sensor (SAS)
  • Poor power or ground to the sensor
  • Damaged wiring or corroded connector
  • CAN/LIN communication error or bus interference
  • Sensor not calibrated or lost calibration after steering work
  • Related ECU (ABS/ESP/steering) fault or software issue

Symptoms

  • ESP/traction control warning lamp illuminated
  • Steering assist or stability functions reduced/disabled
  • Possible steering warning message in dash
  • Fault code stored; intermittent or permanent
  • Inconsistent steering wheel angle readout in diagnostics vs actual wheel position

What to check

  • Read freeze frame and full fault list with a dealer-level scan tool
  • Check live steering angle values and compare to physical wheel position
  • Verify related sensor data (yaw rate, wheel speeds) for plausibility
  • Inspect steering angle sensor connector and wiring for damage, corrosion, or water ingress
  • Measure supply voltage and ground at the sensor connector with ignition on
  • Check CAN/LIN bus health and error counters with a scan tool or oscilloscope

Signal parameters

  • Steering angle output (degrees) — should track physically rotating steering wheel
  • Rate of change (degrees/sec) — should be within plausible limits for driver input
  • Signal format: voltage/analog or digital/CAN message depending on model
  • Checksum or message integrity flags on CAN/LIN frames
  • Supply voltage to sensor (approx. vehicle battery voltage when ON) and solid ground
  • Typical mechanical range: multiple turns of steering wheel (manufacturer dependent; commonly ±720° to ±1080°)

Diagnostic algorithm

  1. Retrieve C2008 and any related codes; note freeze-frame and occurrence count.
  2. With a scan tool, monitor steering angle live data while turning the steering wheel and compare to actual wheel position; check yaw rate and wheel speed agreement.
  3. Visually inspect the SAS connector and wiring harness for corrosion, bent pins, chafing, or water damage; repair as needed.
  4. Measure sensor supply voltage and ground at the connector with ignition ON; verify stable battery voltage.
  5. Check CAN/LIN communication for errors: inspect bus wiring, termination, modules on same bus, and use an oscilloscope if available to confirm message integrity.
  6. If wiring and power are good, perform sensor self-test/calibration using dealer-level diagnostic tool or procedure; recheck fault status.
  7. If implausible values persist after calibration, swap or bench-test the steering angle sensor if possible; replace sensor if confirmed faulty.
  8. After replacement or repair, perform calibration, clear codes, and road test to confirm the fault does not return and related systems operate normally.
  9. If fault remains, pursue module-level diagnostics (ABS/ESP/steering ECU) or software reflash as per factory procedures.

Likely causes

  • Loose/corroded connector or damaged harness at the steering angle sensor
  • Failed steering angle sensor (internal electronics)
  • Loss of sensor calibration (steering wheel not centered after repairs)
  • CAN bus fault causing corrupted or missing SAS messages
  • Low battery/unstable supply voltage to control modules

Fault status

⚠️ Status
Implausible steering angle signal detected — stored by vehicle control module. May be active or intermittent; verify live data and freeze-frame to determine current status.
🟡 Repair difficulty: Medium
⏱️ Diagnostic time: 1.0-3.0 hours

Similar codes

C2006 C2007 C2010 C1216 U1000
Workshop Manuals

Repair manuals for LAND ROVER

3

Land Rover Defender 300Tdi — Workshop Manual (1996 model year)

Workshop Manual
Defender 300Tdi Years: 1996 Manual in English 7.5 MB
Short description

Official workshop manual for the Land Rover Defender 300Tdi (from 1996 model year). Contains specifications, adjustment, fault diagnosis and step-by-step repair and overhaul procedures for engine, transmission, axles, suspension, brakes, electrical and body. Intended for dealer workshops and trained technicians.

199,00 UAH
Contents
Key sections:
  • 01 INTRODUCTION
  • 04 GENERAL SPECIFICATION DATA
  • 05 ENGINE TUNING DATA
  • 07 GENERAL FITTING REMINDERS
  • 09 LUBRICANTS, FLUIDS AND CAPACITIES
  • 10 MAINTENANCE
  • 12 ENGINE Tdi
  • - Description and operation
  • - Fault diagnosis
  • - Adjustment
  • - Repair and overhaul procedures
  • 19 FUEL SYSTEM Tdi
Buy

Land Rover Defender Workshop Manual Supplement & Body Repair Manual (1999 & 2002 MY)

Workshop Manual
Defender Years: 1999–2002 Manual in English 7.6 MB
Short description

Workshop Manual Supplement and Body Repair Manual for the Land Rover Defender. Includes general specifications, maintenance schedules, tuning data and step‑by‑step repair procedures for engine, transmission, suspension, brakes, electrical and body repairs. Covers Defender models from 1999 and 2002 model years.

199,00 UAH
Contents
Key sections:
  • 01 - INTRODUCTION
  • - Introduction
  • - Dimensions
  • - References
  • - Repairs and replacements
  • - Poisonous substances
  • - Fuel handling precautions
  • - Synthetic rubber
  • - Recommended sealants
  • - Used engine oil precautions
  • - Accessories and conversions
  • - Wheels and tyres
Buy

Land Rover Range Rover — Electrical Library (LRL 0453ENG, 2002)

Workshop Manual
Manual in English Pages: 494 7.1 MB
Short description

Land Rover Range Rover Electrical Library (LRL 0453ENG). Comprehensive manual covering fuse details, earth points, system descriptions, diagnostics and connector pin-outs for electrical troubleshooting and repair. Intended for technicians and service workshops.

199,00 UAH
Contents
Key sections:
  • 1 INTRODUCTION
  • 1.1 About this document
  • 1.2 Battery voltage
  • 1.3 Electrical precautions
  • 1.4 Battery disconnecting / charging
  • 1.5 Disciplines / greases
  • 1.6 Abbreviations
  • 1.7 HeVAC, sensors abbreviations
  • 1.8 How to use this document
  • 1.9 Connector detail format
  • 1.10 Fault diagnosis
  • 1.11 Wire colour codes
Buy
Your experience will help others
+100 karma for a short comment :)
Keep it short and practical. Up to 500 characters.
Send to email

Report

Harassment or bullying behavior
Contains mature or sensitive content
Contains misleading or false information
Contains abusive or derogatory content
Contains spam, fake content or potential malware

Block Member?

Please confirm you want to block this member.

You will no longer be able to:

  • See blocked member's posts
  • Mention this member in posts
  • Invite this member to groups
  • Message this member
  • Add this member as a connection

Please note: This action will also remove this member from your connections and send a report to the site admin. Please allow a few minutes for this process to complete.

Report

You have already reported this .