Toggle Side Panel

Shopping Cart

No products in the basket.

Shopping Cart

No products in the basket.

Close search
Home / DTC / B13CC — Right - Static lighting lamp - Electrical supply

B13CC — Right - Static lighting lamp - Electrical supply

Detailed page for trouble code B13CC.

32,998codes
59brands
10,537generic
22,461specific
All codes P-codes (Powertrain) B-codes (Body) C-codes (Chassis) U-codes (Network/User) Tesla Alerts
Reset
Code

B13CC

LAND ROVER B — Body

Right - Static lighting lamp - Electrical supply

Brand: LAND ROVER
Type: B — Body
Views: UK: 6 EN: 11 RU: 7
AI status
Completed
ready
Completed 100%
Page language: EN

Causes

  • Blown bulb or failed LED unit
  • Blown fuse or tripped circuit protection
  • Open, corroded or loose connector at the right static lamp
  • Broken or chafed wire in the harness (open or short to ground/12V)
  • Poor ground connection at lamp or body earth
  • Corrosion or water ingress at lamp housing or connector

Symptoms

  • Right static/parking/position lamp does not illuminate
  • Intermittent illumination or flicker of the right static lamp
  • Instrument cluster or message centre lamp fault/warning displayed
  • Related lighting functions operate normally on the left side
  • Possible multiple lighting DTCs if a module output is shorted

What to check

  • Read stored and pending DTCs and any related body network codes using a capable scan tool
  • Visually inspect the right static lamp assembly, socket and connector for corrosion, water, damage or loose pins
  • Inspect wiring harness along route for damage, repairs or pinched sections
  • Check relevant fuses and fuseholder contacts
  • Remove bulb or lamp module and inspect/measure filament or LED unit resistance
  • With lamp connector disconnected, check for corrosion and bent pins

Signal parameters

  • Expected supply voltage at lamp connector: battery voltage (~11.5–14.5 V) when lights are on (no excessive voltage drop)
  • Typical incandescent parking lamp resistance: ~5–10 Ω (varies by lamp wattage) — LED assemblies will show much higher/complex resistance; check manufacturer specs
  • Current draw for incandescent parking lamp: roughly 0.3–1.0 A (depends on lamp wattage); LED much lower and may require CAN/driver checks
  • Acceptable voltage drop between module feed and lamp connector:
  • Ground continuity: near 0 Ω between lamp ground pin and vehicle chassis ground
  • If lamp driver is PWM, frequency may be present — use an oscilloscope or diagnostic tool to view duty cycle and frequency

Diagnostic algorithm

  1. Connect a capable scan tool. Read and record DTC B13CC and any related codes. Note freeze-frame/live-data.
  2. Perform a visual inspection of the right static lamp assembly, socket and adjacent wiring. Check for moisture, corrosion or physical damage.
  3. Check fuses/circuit breakers for the lighting circuit. Replace/test fuse and fuseholder if suspect.
  4. Remove the lamp/bulb and inspect the lamp element. Test lamp continuity/resistance. Replace lamp if open or visibly failed.
  5. With connector disconnected, measure supply voltage at the lamp feed pin with lights ON. If battery voltage is present, measure ground continuity at the ground pin.
  6. If no supply voltage, trace back to the fuse and BCM output. Check for voltage at BCM connector or intermediate splice. Repair/open circuit as found.
  7. If supply voltage present but lamp does not illuminate, apply a fused 12V bench supply to the lamp connector to verify lamp/LED operation and isolate wiring.
  8. If supply is low or intermittent, perform wiggle test and probe wiring for intermittent shorts/opens. Repair harness damage and secure routing.
  9. If a short to ground or to 12V is suspected, isolate circuit sections and measure resistance to identify short location. Repair or replace wiring as required.
  10. If wiring and lamp check good, test/replace the body control module/lighting driver or its connector only after confirming a good wiring harness and verifying the module output is faulty.
  11. Clear codes and re-test operation. Confirm repair by road test and checking for reappearance of the code.

Likely causes

  • Blown lamp filament or failed LED assembly
  • Corroded/loose connector pins at the lamp socket
  • Broken conductor in the right front/rear harness (pinched or rubbed through)
  • Failed ground/earth strap at lamp mounting point
  • Open fuse or poor fuse contact
  • Faulty lamp output transistor inside BCM or damaged connector at module

Fault status

⚠️ Status
Right static lighting lamp — electrical supply fault detected (circuit supply voltage out of range, open or short). Lamp may be inoperative or intermittent.
🟡 Repair difficulty: Medium
⏱️ Diagnostic time: 0.5-2.0 hours

Similar codes

B13CA B13CB B13CD B13CE U0135
Workshop Manuals

Repair manuals for LAND ROVER

3

Land Rover Defender 300Tdi — Workshop Manual (1996 model year)

Workshop Manual
Defender 300Tdi Years: 1996 Manual in English 7.5 MB
Short description

Official workshop manual for the Land Rover Defender 300Tdi (from 1996 model year). Contains specifications, adjustment, fault diagnosis and step-by-step repair and overhaul procedures for engine, transmission, axles, suspension, brakes, electrical and body. Intended for dealer workshops and trained technicians.

199,00 UAH
Contents
Key sections:
  • 01 INTRODUCTION
  • 04 GENERAL SPECIFICATION DATA
  • 05 ENGINE TUNING DATA
  • 07 GENERAL FITTING REMINDERS
  • 09 LUBRICANTS, FLUIDS AND CAPACITIES
  • 10 MAINTENANCE
  • 12 ENGINE Tdi
  • - Description and operation
  • - Fault diagnosis
  • - Adjustment
  • - Repair and overhaul procedures
  • 19 FUEL SYSTEM Tdi
Buy

Land Rover Defender Workshop Manual Supplement & Body Repair Manual (1999 & 2002 MY)

Workshop Manual
Defender Years: 1999–2002 Manual in English 7.6 MB
Short description

Workshop Manual Supplement and Body Repair Manual for the Land Rover Defender. Includes general specifications, maintenance schedules, tuning data and step‑by‑step repair procedures for engine, transmission, suspension, brakes, electrical and body repairs. Covers Defender models from 1999 and 2002 model years.

199,00 UAH
Contents
Key sections:
  • 01 - INTRODUCTION
  • - Introduction
  • - Dimensions
  • - References
  • - Repairs and replacements
  • - Poisonous substances
  • - Fuel handling precautions
  • - Synthetic rubber
  • - Recommended sealants
  • - Used engine oil precautions
  • - Accessories and conversions
  • - Wheels and tyres
Buy

Land Rover Range Rover — Electrical Library (LRL 0453ENG, 2002)

Workshop Manual
Manual in English Pages: 494 7.1 MB
Short description

Land Rover Range Rover Electrical Library (LRL 0453ENG). Comprehensive manual covering fuse details, earth points, system descriptions, diagnostics and connector pin-outs for electrical troubleshooting and repair. Intended for technicians and service workshops.

199,00 UAH
Contents
Key sections:
  • 1 INTRODUCTION
  • 1.1 About this document
  • 1.2 Battery voltage
  • 1.3 Electrical precautions
  • 1.4 Battery disconnecting / charging
  • 1.5 Disciplines / greases
  • 1.6 Abbreviations
  • 1.7 HeVAC, sensors abbreviations
  • 1.8 How to use this document
  • 1.9 Connector detail format
  • 1.10 Fault diagnosis
  • 1.11 Wire colour codes
Buy
Your experience will help others
+100 karma for a short comment :)
Keep it short and practical. Up to 500 characters.
Send to email

Report

Harassment or bullying behavior
Contains mature or sensitive content
Contains misleading or false information
Contains abusive or derogatory content
Contains spam, fake content or potential malware

Block Member?

Please confirm you want to block this member.

You will no longer be able to:

  • See blocked member's posts
  • Mention this member in posts
  • Invite this member to groups
  • Message this member
  • Add this member as a connection

Please note: This action will also remove this member from your connections and send a report to the site admin. Please allow a few minutes for this process to complete.

Report

You have already reported this .