Toggle Side Panel

Shopping Cart

No products in the basket.

Shopping Cart

No products in the basket.

Close search
Home / DTC / P0114 — Intake Air Temperature Sensor 1 Circuit Intermittent Bank 1

P0114 — Intake Air Temperature Sensor 1 Circuit Intermittent Bank 1

Detailed page for trouble code P0114.

34,405codes
59brands
11,914generic
22,491specific
All codes P-codes (Powertrain) B-codes (Body) C-codes (Chassis) U-codes (Network/User) Tesla Alerts
Reset
Code

P0114

Generic P — Powertrain

Intake Air Temperature Sensor 1 Circuit Intermittent Bank 1

Brand: Generic
Type: P — Powertrain
AI status
Completed
ready
Completed 100%
Page language: EN

Causes

  • Corroded, loose, or damaged IAT sensor connector or pins
  • Broken or chafed wiring harness between IAT sensor and ECM
  • Intermittent short to voltage or ground in the IAT circuit
  • Failed IAT sensor (thermistor intermittent)
  • Poor engine/ECM ground or reference voltage supply
  • Intermittent ECM input circuit fault or solder joint

Symptoms

  • Malfunction Indicator Lamp (MIL) may illuminate sporadically
  • Intermittent rough idle, hesitation or stumbling under load
  • Erratic fuel trim behavior, occasional increased fuel consumption
  • Difficult or inconsistent cold starts (possible)
  • No constant sensor reading for intake temperature on scan tool (fluctuating or dropping to open)

What to check

  • Scan tool: read IAT PID while engine cold to warm and observe for dropouts or erratic jumps
  • Check freeze frame / freeze data and frequency of fault occurrence
  • Visually inspect IAT sensor connector and wiring for damage, corrosion, or looseness
  • Backprobe connector and check reference voltage and signal with ignition ON/engine running
  • Measure sensor resistance at the harness connector (with sensor disconnected) and compare to expected thermistor behavior as temperature changes
  • Perform wiggle test on harness and connector while monitoring IAT PID/voltage for intermittent changes

Signal parameters

  • Sensor type: normally an NTC thermistor (resistance decreases as temp rises)
  • Expected signal voltage: typically in the 0.1–4.9 V range depending on intake temp and vehicle design
  • Typical resistance at ~20°C: on many vehicles roughly 1–10 kΩ (varies by manufacturer)
  • Open-circuit: signal voltage often near reference supply (or diagnostic tool shows OL/infinite resistance)
  • Short to ground: signal voltage near 0 V; short to battery: signal near reference voltage (~5 V)

Diagnostic algorithm

  1. Retrieve freeze frame and clear code; attempt to recreate fault by cycling ignition/engine and monitor IAT PID for intermittent behavior
  2. Visually inspect sensor, connector, and wiring harness; repair visible damage, corrosion, or bent pins
  3. Backprobe IAT connector: with ignition ON measure reference voltage (if applicable) and signal voltage while varying intake air temperature (or blow air/cold spray) — signal should move smoothly
  4. Measure sensor resistance at sensor leads (disconnect sensor). Compare to a known thermistor resistance vs temperature chart for the vehicle or general NTC behavior. Replace sensor if values are out of expected range or erratic
  5. Perform continuity/resistance check from sensor connector to ECM input pin; wiggle harness to look for intermittent opens
  6. If intermittent voltage spikes or noise are seen, inspect/repair grounds and any shielding; install/repair grounds as needed
  7. If wiring and sensor test good but intermittent signal persists, swap/replace the IAT sensor with a known-good unit and retest
  8. If intermittent persists after harness and sensor replacement, consider ECM input circuit fault — consult service information and consider ECM bench test/replacement

Likely causes

  • Damaged/loose connector at IAT sensor
  • Frayed or intermittent wiring (chafe/wire break) between sensor and ECM
  • Failing IAT sensor element (internal intermittent)
  • Corrosion or poor contact at mating connector pins
  • ECM input/ground problem (less common)

Fault status

⚠️ Status
Intermittent fault reported in Intake Air Temperature Sensor 1 circuit (Bank 1). ECM detected an unstable/open/short/erratic IAT signal condition; fault set intermittently rather than continuously.
🟡 Repair difficulty: Medium
⏱️ Diagnostic time: 0.5-2 hours

Similar codes

P0113 P0112 P0115 P0118 P0102 P0103
9,036

The library contains 9,036 repair and diagnostic manuals. Choose a brand to open the full manual tree by year, model and trim.

ALFA ROMEO
89
AUDI
1,243
BMW
479
CADILLAC
206
CHEVROLET
456
CHRYSLER
122
DAEWOO
75
FIAT
26
GENESIS
207
HUMMER
138
HYUNDAI
371
ISUZU
86
LAND ROVER
320
LEXUS
280
LINCOLN
166
MERCEDES-BENZ
856
MERCURY
296
MITSUBISHI
406
PORSCHE
136
TESLA
58
TOYOTA
2,042
TRIUMPH
131
VOLKSWAGEN
626
VOLVO
221
Your experience will help others
+100 karma for a short comment :)
Keep it short and practical. Up to 500 characters.
Send to email
Code

P0114

GWM P — Powertrain

- Inlet air temperature sensor fault

Brand: GWM
Type: P — Powertrain
AI status
Completed
ready
Completed 100%
Page language: EN

Causes

  • Corroded, loose, or damaged IAT sensor connector or pins
  • Broken or chafed wiring harness between IAT sensor and ECM
  • Intermittent short to voltage or ground in the IAT circuit
  • Failed IAT sensor (thermistor intermittent)
  • Poor engine/ECM ground or reference voltage supply
  • Intermittent ECM input circuit fault or solder joint

Symptoms

  • Malfunction Indicator Lamp (MIL) may illuminate sporadically
  • Intermittent rough idle, hesitation or stumbling under load
  • Erratic fuel trim behavior, occasional increased fuel consumption
  • Difficult or inconsistent cold starts (possible)
  • No constant sensor reading for intake temperature on scan tool (fluctuating or dropping to open)

What to check

  • Scan tool: read IAT PID while engine cold to warm and observe for dropouts or erratic jumps
  • Check freeze frame / freeze data and frequency of fault occurrence
  • Visually inspect IAT sensor connector and wiring for damage, corrosion, or looseness
  • Backprobe connector and check reference voltage and signal with ignition ON/engine running
  • Measure sensor resistance at the harness connector (with sensor disconnected) and compare to expected thermistor behavior as temperature changes
  • Perform wiggle test on harness and connector while monitoring IAT PID/voltage for intermittent changes

Signal parameters

  • Sensor type: normally an NTC thermistor (resistance decreases as temp rises)
  • Expected signal voltage: typically in the 0.1–4.9 V range depending on intake temp and vehicle design
  • Typical resistance at ~20°C: on many vehicles roughly 1–10 kΩ (varies by manufacturer)
  • Open-circuit: signal voltage often near reference supply (or diagnostic tool shows OL/infinite resistance)
  • Short to ground: signal voltage near 0 V; short to battery: signal near reference voltage (~5 V)

Diagnostic algorithm

  1. Retrieve freeze frame and clear code; attempt to recreate fault by cycling ignition/engine and monitor IAT PID for intermittent behavior
  2. Visually inspect sensor, connector, and wiring harness; repair visible damage, corrosion, or bent pins
  3. Backprobe IAT connector: with ignition ON measure reference voltage (if applicable) and signal voltage while varying intake air temperature (or blow air/cold spray) — signal should move smoothly
  4. Measure sensor resistance at sensor leads (disconnect sensor). Compare to a known thermistor resistance vs temperature chart for the vehicle or general NTC behavior. Replace sensor if values are out of expected range or erratic
  5. Perform continuity/resistance check from sensor connector to ECM input pin; wiggle harness to look for intermittent opens
  6. If intermittent voltage spikes or noise are seen, inspect/repair grounds and any shielding; install/repair grounds as needed
  7. If wiring and sensor test good but intermittent signal persists, swap/replace the IAT sensor with a known-good unit and retest
  8. If intermittent persists after harness and sensor replacement, consider ECM input circuit fault — consult service information and consider ECM bench test/replacement

Likely causes

  • Damaged/loose connector at IAT sensor
  • Frayed or intermittent wiring (chafe/wire break) between sensor and ECM
  • Failing IAT sensor element (internal intermittent)
  • Corrosion or poor contact at mating connector pins
  • ECM input/ground problem (less common)

Fault status

⚠️ Status
Intermittent fault reported in Intake Air Temperature Sensor 1 circuit (Bank 1). ECM detected an unstable/open/short/erratic IAT signal condition; fault set intermittently rather than continuously.
🟡 Repair difficulty: Medium
⏱️ Diagnostic time: 0.5-2 hours

Similar codes

P0113 P0112 P0115 P0118 P0102 P0103
Your experience will help others
+100 karma for a short comment :)
Keep it short and practical. Up to 500 characters.
Send to email
Code

P0114

HUMMER P — Powertrain

Intake Air Temperature Circuit Intermittent

Brand: HUMMER
Type: P — Powertrain
AI status
Completed
ready
Completed 100%
Page language: EN

Causes

  • Corroded, loose, or damaged IAT sensor connector or pins
  • Broken or chafed wiring harness between IAT sensor and ECM
  • Intermittent short to voltage or ground in the IAT circuit
  • Failed IAT sensor (thermistor intermittent)
  • Poor engine/ECM ground or reference voltage supply
  • Intermittent ECM input circuit fault or solder joint

Symptoms

  • Malfunction Indicator Lamp (MIL) may illuminate sporadically
  • Intermittent rough idle, hesitation or stumbling under load
  • Erratic fuel trim behavior, occasional increased fuel consumption
  • Difficult or inconsistent cold starts (possible)
  • No constant sensor reading for intake temperature on scan tool (fluctuating or dropping to open)

What to check

  • Scan tool: read IAT PID while engine cold to warm and observe for dropouts or erratic jumps
  • Check freeze frame / freeze data and frequency of fault occurrence
  • Visually inspect IAT sensor connector and wiring for damage, corrosion, or looseness
  • Backprobe connector and check reference voltage and signal with ignition ON/engine running
  • Measure sensor resistance at the harness connector (with sensor disconnected) and compare to expected thermistor behavior as temperature changes
  • Perform wiggle test on harness and connector while monitoring IAT PID/voltage for intermittent changes

Signal parameters

  • Sensor type: normally an NTC thermistor (resistance decreases as temp rises)
  • Expected signal voltage: typically in the 0.1–4.9 V range depending on intake temp and vehicle design
  • Typical resistance at ~20°C: on many vehicles roughly 1–10 kΩ (varies by manufacturer)
  • Open-circuit: signal voltage often near reference supply (or diagnostic tool shows OL/infinite resistance)
  • Short to ground: signal voltage near 0 V; short to battery: signal near reference voltage (~5 V)

Diagnostic algorithm

  1. Retrieve freeze frame and clear code; attempt to recreate fault by cycling ignition/engine and monitor IAT PID for intermittent behavior
  2. Visually inspect sensor, connector, and wiring harness; repair visible damage, corrosion, or bent pins
  3. Backprobe IAT connector: with ignition ON measure reference voltage (if applicable) and signal voltage while varying intake air temperature (or blow air/cold spray) — signal should move smoothly
  4. Measure sensor resistance at sensor leads (disconnect sensor). Compare to a known thermistor resistance vs temperature chart for the vehicle or general NTC behavior. Replace sensor if values are out of expected range or erratic
  5. Perform continuity/resistance check from sensor connector to ECM input pin; wiggle harness to look for intermittent opens
  6. If intermittent voltage spikes or noise are seen, inspect/repair grounds and any shielding; install/repair grounds as needed
  7. If wiring and sensor test good but intermittent signal persists, swap/replace the IAT sensor with a known-good unit and retest
  8. If intermittent persists after harness and sensor replacement, consider ECM input circuit fault — consult service information and consider ECM bench test/replacement

Likely causes

  • Damaged/loose connector at IAT sensor
  • Frayed or intermittent wiring (chafe/wire break) between sensor and ECM
  • Failing IAT sensor element (internal intermittent)
  • Corrosion or poor contact at mating connector pins
  • ECM input/ground problem (less common)

Fault status

⚠️ Status
Intermittent fault reported in Intake Air Temperature Sensor 1 circuit (Bank 1). ECM detected an unstable/open/short/erratic IAT signal condition; fault set intermittently rather than continuously.
🟡 Repair difficulty: Medium
⏱️ Diagnostic time: 0.5-2 hours

Similar codes

P0113 P0112 P0115 P0118 P0102 P0103
Repair manuals

Manual library for HUMMER

138

Browse 138 HUMMER manuals: repair procedures, diagnostics, wiring diagrams, component locations, service data and Labor Times by year, model and trim.

HUMMER

Your experience will help others
+100 karma for a short comment :)
Keep it short and practical. Up to 500 characters.
Send to email
Code

P0114

LAND ROVER P — Powertrain

Intake Air Temperature Sensor 1 - Circuit

Brand: LAND ROVER
Type: P — Powertrain
AI status
Completed
ready
Completed 100%
Page language: EN

Causes

  • Corroded, loose, or damaged IAT sensor connector or pins
  • Broken or chafed wiring harness between IAT sensor and ECM
  • Intermittent short to voltage or ground in the IAT circuit
  • Failed IAT sensor (thermistor intermittent)
  • Poor engine/ECM ground or reference voltage supply
  • Intermittent ECM input circuit fault or solder joint

Symptoms

  • Malfunction Indicator Lamp (MIL) may illuminate sporadically
  • Intermittent rough idle, hesitation or stumbling under load
  • Erratic fuel trim behavior, occasional increased fuel consumption
  • Difficult or inconsistent cold starts (possible)
  • No constant sensor reading for intake temperature on scan tool (fluctuating or dropping to open)

What to check

  • Scan tool: read IAT PID while engine cold to warm and observe for dropouts or erratic jumps
  • Check freeze frame / freeze data and frequency of fault occurrence
  • Visually inspect IAT sensor connector and wiring for damage, corrosion, or looseness
  • Backprobe connector and check reference voltage and signal with ignition ON/engine running
  • Measure sensor resistance at the harness connector (with sensor disconnected) and compare to expected thermistor behavior as temperature changes
  • Perform wiggle test on harness and connector while monitoring IAT PID/voltage for intermittent changes

Signal parameters

  • Sensor type: normally an NTC thermistor (resistance decreases as temp rises)
  • Expected signal voltage: typically in the 0.1–4.9 V range depending on intake temp and vehicle design
  • Typical resistance at ~20°C: on many vehicles roughly 1–10 kΩ (varies by manufacturer)
  • Open-circuit: signal voltage often near reference supply (or diagnostic tool shows OL/infinite resistance)
  • Short to ground: signal voltage near 0 V; short to battery: signal near reference voltage (~5 V)

Diagnostic algorithm

  1. Retrieve freeze frame and clear code; attempt to recreate fault by cycling ignition/engine and monitor IAT PID for intermittent behavior
  2. Visually inspect sensor, connector, and wiring harness; repair visible damage, corrosion, or bent pins
  3. Backprobe IAT connector: with ignition ON measure reference voltage (if applicable) and signal voltage while varying intake air temperature (or blow air/cold spray) — signal should move smoothly
  4. Measure sensor resistance at sensor leads (disconnect sensor). Compare to a known thermistor resistance vs temperature chart for the vehicle or general NTC behavior. Replace sensor if values are out of expected range or erratic
  5. Perform continuity/resistance check from sensor connector to ECM input pin; wiggle harness to look for intermittent opens
  6. If intermittent voltage spikes or noise are seen, inspect/repair grounds and any shielding; install/repair grounds as needed
  7. If wiring and sensor test good but intermittent signal persists, swap/replace the IAT sensor with a known-good unit and retest
  8. If intermittent persists after harness and sensor replacement, consider ECM input circuit fault — consult service information and consider ECM bench test/replacement

Likely causes

  • Damaged/loose connector at IAT sensor
  • Frayed or intermittent wiring (chafe/wire break) between sensor and ECM
  • Failing IAT sensor element (internal intermittent)
  • Corrosion or poor contact at mating connector pins
  • ECM input/ground problem (less common)

Fault status

⚠️ Status
Intermittent fault reported in Intake Air Temperature Sensor 1 circuit (Bank 1). ECM detected an unstable/open/short/erratic IAT signal condition; fault set intermittently rather than continuously.
🟡 Repair difficulty: Medium
⏱️ Diagnostic time: 0.5-2 hours

Similar codes

P0113 P0112 P0115 P0118 P0102 P0103
320

Browse 320 LAND ROVER manuals: repair procedures, diagnostics, wiring diagrams, component locations, service data and Labor Times by year, model and trim.

LAND ROVER

Your experience will help others
+100 karma for a short comment :)
Keep it short and practical. Up to 500 characters.
Send to email

Report

Harassment or bullying behavior
Contains mature or sensitive content
Contains misleading or false information
Contains abusive or derogatory content
Contains spam, fake content or potential malware

Block Member?

Please confirm you want to block this member.

You will no longer be able to:

  • See blocked member's posts
  • Mention this member in posts
  • Invite this member to groups
  • Message this member
  • Add this member as a connection

Please note: This action will also remove this member from your connections and send a report to the site admin. Please allow a few minutes for this process to complete.

Report

You have already reported this .